Pre-Startup Checklist

Note: FOR LONE STAR TURBO STARTUP SERVICES, PLEASE COMPLETE THE FOLLOWING FORMS AND SUBMIT TO LONE STAR TURBO. PLEASE ALLOW 4 WEEKS FOR SCHEDULING OF LONE STAR PERSONNEL.

ATTACH ALL REQUESTED PHOTOS TO END OF THIS REPORT

NOTE: Please take the time to complete our pre-startup checklist below. Thank you for your business and have a great day!

- Step 1 of 7

ANY DEFICIENCIES NOTED BY LONE STAR WILL BE SENT TO CUSTOMER AND WILL NEED TO BE ADDRESSED BEFORE STARTUP IS APPROVED OR STARTUP SERVICES ARE PROVIDED BY LONE STAR PERSONNEL.

Client Details

Company *

Facility Name *

Physical Facility Address *

Address Line 1

Address Line 2

City

State / Province / Region

Postal Code

Country

Contact Name *

First

Last

Facility Identifier *

Contact Phone *

LST Job # *

Model #

Email *

Manufacturer *

Serial #

Date of Inspection *

ATTACH ALL REQUESTED PHOTOS TO END OF EACH SECTION OF THIS REPORT

Save and Resume Later

IO&M

END USER/FACILITY PERSONNEL have the correct IO&M manual? *

Is all pertinent information for all accessories included? *

Have required site personnel reviewed IO&M? *

INSTALLATION

Location *

Indoors
Outdoors

Please include wide vantage photo(s) of unit installation.

If Outdoors *

Covered
Uncovered

Please include wide vantage photo(s) of unit installation.

Photos of Location - Outdoors

Drag & Drop Files, Choose Files to Upload

FOUNDATION

Type of foundation *

Individual Base
Common Base

Is foundation level within specified requirements? *

Specification requirement is 1/16” per foot slope or maximum of 1/8” over length and width of base, whichever is less. Please include picture(s) of foundation and measurements.

Please include picture of foundation and measurements *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Are vibration pads in proper location per GA drawings provided? *

Please include picture(s) of vibration pads with machine in place.

Please include picture of vibration pads with machine in place. *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Do locating studs have clearance from base of machine (not contacting base)? *

Please include picture(s) of locating studs with machine in place.

Please include picture of locating studs with machine in place. *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Are foundation studs loosened to allow for vibration to dissipate? *

If on common base, is common base grouted in? *

Please include picture of common base grouted in place *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

If any answer is no, please explain below. *

Save and Resume Later

PIPING

Is piping adequately supported (no weight is on blower inlet or discharge)? *

All covers are removed from blower and site piping? *

INLET PIPING

Are flexible connectors installed on inlet? *

Inlet Piping Type? *

Sleeve
Elastomer type

Please include picture of inlet piping with all components installed *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Is piping aligned with blower inlet (no angularity between flanges)? *

Please include picture of inlet piping with all components installed

Is inlet valve in correct orientation and location? *

inlet-valve-location

Is inlet valve free to open and close? *

Yes
No
Not Installed

Are locks working properly? *

Yes
No
Not Installed

Valve shaft is at right angle to blower shaft? *

Yes
No
Not Installed

Actuator installed correctly? *

Yes
No
Not Installed

If unit is used on vacuum, please complete the following question. Is check valve installed in proper orientation? *

Yes
No
Not Installed
N/A

Is check valve upstream of the blow-off valve? *

If any answer is no, please explain below. *

DISCHARGE PIPING

Are flexible connectors installed on discharge? *

Type? *

Sleeve
Elastomer type

Is piping aligned with blower discharge (no angularity between flanges)? *

Please include picture of discharge piping with all components installed *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Is check valve installed in proper orientation? *

Is a blow-off valve installed? *

Yes
No
Not Installed

Is check valve downstream of the blow-off valve? *

Is piping aligned with blower inlet (no angularity between flanges)? *

Please include picture(s) of discharge piping with all components installed

Is discharge valve in correct orientation and location? *

Yes
No
Not Installed

Is inlet valve free to open and close? *

Yes
No
Not Installed

Are locks working properly? *

Yes
No
Not Installed

Valve shaft is at parallel to blower shaft? *

Yes
No
Not Installed

Actuator installed correctly? *

Yes
No
Not Installed

If any answer is no, please explain below. *

Save and Resume Later

PRE-STARTUP

NON-INSTRUMENT ACCESSORIES

Is unit equipped with an air filter? *

Yes
No
Not Installed

Brand

Model

Material type *

Paper
Felt
Wire Type

Is unit equipped with silencers? INLET *

Yes
No
Not Installed

Is unit equipped with silencers? DISCHARGE *

Yes
No
Not Installed

Is unit equipped with pressure relief valve? *

Yes
No
Not Installed

Please include picture(s) of filter assembly installed on blower.

Please include picture of filter assembly installed on blower *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Please verify ORDERED accessories from FDS and shipping documents. Was unit sent without any of the ordered components listed above? *

Additional Comments

BLOWER CONDITION

Has blower been properly maintained during storage using manufacturer recommended procedures? *

Blower is free of visible damage? *

Does shaft rotate freely? *

Drive Type *

Belt Driven
Direct Coupled

Please include picture(s) of drive system installed on blower.

Number of belts *

Belt model number *

Sheave diameter motor *

Sheave diameter blower *

If direct coupled, please answer the following questions and fill out table. Coupling type *

Elastomer type
Disc shim pack type

Coupling size *

Coupling manufacturer *

Please include picture of drive system installed on blower *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Additional comments

Save and Resume Later

LUBRICATION SYSTEM

Lubrication type used for blower *

Grease
Oil

No visible leaks of lubrication system present? *

For grease lubricated units. Additional grease on site? *

Grease type used *

For oil lubricated units. Additional oil on site? *

Please include picture(s) of oiler system installed on blower.

Oil type used *

Constant level oilers installed? *

No visible damage to oilers? *

Oil level correct? *

Oil level full? *

Please include picture of oiler system installed on blower *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Motor

Lubrication type used for motor *

Grease
Oil

No visible leaks of lubrication system present? *

For grease lubricated units. Additional grease on site? *

Grease type used *

Has motor been lubricated per OEM requirements? *

Note: Grease lubricated blowers do not require additional grease at startup unless authorized by Lone Star Turbo personnel.

For oil lubricated units. Additional oil on site? *

Oil type used *

Constant level oilers installed? *

No visible damage to oilers? *

Oil level correct? *

Oil level full? *

Additional comments

Please include several pictures from various angles of motor installation including oilers if installed *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

Save and Resume Later

STARTING/RUN EQUIPMENT

Is unit using a direct on the line, soft starter or VFD? *

Direct on line
Soft Starter
VFD
Other

Please explain Other

If using soft starter, is unit wired correctly?

Are all parameters verified for soft starter or VFD? *

installed downstream with

Has rotation been bumped to verify correct rotation direction? *

Are multiple units to be run in parallel? *

Number of units run in parallel

Additional comments

Please include picture of starting equipment *

Drag & Drop Files, Choose Files to Upload You can upload up to 20 files.

INSTRUMENTATION

Is a current transducer installed? *

Is the current transducer reading/scaled correctly? *

Are all transmitters installed and wired correctly? *

Are transmitters reading properly? *

Is control panel installed and wired correctly? *

Does HMI power up properly? *

Machine displays no errors or alarms on power up? *

If any answer was no, please explain below.

Please use this section for any additional observations or comments

Foundation & Messurements, Vibration Pads with Machine in Place, Locating Studs with Machine in place, Common base grouted in place, Inlet piping with all components installed, Discharge piping with all components installed, Filter assembly installed on blower, Drive System installed on blower, Oiler System installed on blower, Various angles of Motor Installation including Oilers if installed

Please include requested pictures you may have not uploaded.

Drag & Drop Files, Choose Files to Upload You can upload up to 100 files.

Save and Resume Later

Authorization Signature

I confirm that this blower and related equipment are fully installed and ready for startup by Lone Star Turbo personnel or designated representatives. Furthermore, I understand that any delays incurred because of incomplete or incorrect installation will result in additional charges per Lone Star Turbo’s published field service rates.

Company *

Blower Serial # *

Customer Signature *

Clear Signature

Print Name *

First

Last

Effective Date *

Save and Resume Later

Your form entry has been saved and a unique link has been created which you can access to resume this form. Enter your email address to receive the link via email. Alternatively, you can copy and save the link below. Please note, this link should not be shared and will expire in 30 days, afterwards your form entry will be deleted.

Copy Link

Email *